Home › Beauty accessories › Dual-Action Gravity Airbrush Set for Cak
Beauty accessories
Dual-Action Gravity Airbrush Set for Cake Nail Art (AB-130K)
US$22.80
Minimum order: 100 Pieces
SupplierNingbo Joystar Tools Co., Ltd.
LocationNingbo, Zhejiang, China
Certification—
Factory addressRoom302, Building 3, No. 988 Jinyuan Road, Yinzhou, Ningbo, Zhejiang, China
Certifications—
Product Photos
Product Details
Product Description
Product Name: Airbrush Kit
Model: AB-130K
Specification:
Nozzle Diameter: 0.2 & 0.3 & 0.5mm to Swap
Fluid Cup Capacity: 7cc
Operating Pressure: 15-50 PSI
Switch Mode: Dual-Action Trigger Control
Paint Distance: 50 ~ 100mm
Length of Spray Pen: 5.67"/ 14.4 cm
Color: Silver
Package:
Carton Dimension: 50x38x31 CM
PCS/CTN: 20
N.W./G.W.: 16/18 KG
Used for: Airbrush makeup, Airbrush tattoo, Airbrush tanning, Finger nail art, Automotive, Cake, Hobby
How to clean the airbrush:
Setp1:
After spraying your project and your ready to clean the paint from the Airbrush, or you are just ready for a color change, discard the paint from the color cup with a squeeze bottle and use a cleaning brush to clean the color cup immediately. Remember to never let any paint dry or sit in the Airbrush as this will cause a world of problems for you.
Step2:
Now, using a bucket of fresh water (the bucket is to minimize over-spray in the air), submerge the Airbrush underwater and perform the "flush and back-flush" steps. This is where you allow clean water to run through the Airbrush and then allowing water to back-flush any pigment inside of it. This is achieved by "plugging" and "un-plugging" the tip (needle cap) of the brush with your finger. Do this 10-20 times underwater or until clean.
Step3:
Note: Although the color cup and airbrush visibly appear to be clean, there may still be pigment inside the body of the brush AND on the needle. Remove the needle by loosening the needle chuck and wipe the needle clean. While the needle is out, you can flush and back-flush the Airbrush through fresh water to insure it is 100% clean. Now you can gently replace the needle. (be very soft handed and be careful replacing the needle as to avoid damaging the fluid nozzle.)
Step4:
Airbrush cleaner can now be added to the brush to eat away any stubborn paint still inside the brush. (If you are using auto paint, use reducer as your cleaner). Flush and back-flush a few times and spray out the cleaner to get a visual spray test. If a sputtering or spitting pattern comes out, your brush is still dirty and you will need to repeat steps 1-4.
Model: AB-130K
Specification:
Nozzle Diameter: 0.2 & 0.3 & 0.5mm to Swap
Fluid Cup Capacity: 7cc
Operating Pressure: 15-50 PSI
Switch Mode: Dual-Action Trigger Control
Paint Distance: 50 ~ 100mm
Length of Spray Pen: 5.67"/ 14.4 cm
Color: Silver
Package:
Carton Dimension: 50x38x31 CM
PCS/CTN: 20
N.W./G.W.: 16/18 KG
Used for: Airbrush makeup, Airbrush tattoo, Airbrush tanning, Finger nail art, Automotive, Cake, Hobby
How to clean the airbrush:
Setp1:
After spraying your project and your ready to clean the paint from the Airbrush, or you are just ready for a color change, discard the paint from the color cup with a squeeze bottle and use a cleaning brush to clean the color cup immediately. Remember to never let any paint dry or sit in the Airbrush as this will cause a world of problems for you.
Step2:
Now, using a bucket of fresh water (the bucket is to minimize over-spray in the air), submerge the Airbrush underwater and perform the "flush and back-flush" steps. This is where you allow clean water to run through the Airbrush and then allowing water to back-flush any pigment inside of it. This is achieved by "plugging" and "un-plugging" the tip (needle cap) of the brush with your finger. Do this 10-20 times underwater or until clean.
Step3:
Note: Although the color cup and airbrush visibly appear to be clean, there may still be pigment inside the body of the brush AND on the needle. Remove the needle by loosening the needle chuck and wipe the needle clean. While the needle is out, you can flush and back-flush the Airbrush through fresh water to insure it is 100% clean. Now you can gently replace the needle. (be very soft handed and be careful replacing the needle as to avoid damaging the fluid nozzle.)
Step4:
Airbrush cleaner can now be added to the brush to eat away any stubborn paint still inside the brush. (If you are using auto paint, use reducer as your cleaner). Flush and back-flush a few times and spray out the cleaner to get a visual spray test. If a sputtering or spitting pattern comes out, your brush is still dirty and you will need to repeat steps 1-4.
Factory Profile
CompanyNingbo Joystar Tools Co., Ltd.
Business typeManufacturer/Factory, Trading Company
AddressRoom302, Building 3, No. 988 Jinyuan Road, Yinzhou, Ningbo, Zhejiang, China
LocationNingbo, Zhejiang, China
Certifications—
Main productsSpray Gun, Airbrush, Dental Compressor More
More from this factory
Airbrush Makeup Nail Art Compressor with Hose (AC01)
Airbrush Compressor for Nail Art (AC02)
Airbrush Tattoo Compressor for Nail Art (AC03mini)
Airbrush Compressor Kit for Nail Art (AC07K)
Portable Mini Air Compressor for Nail Art (AC05)
Airbrush Mini Compressor for Nail Art (AC07)
electric nail art Polish tool set (ED-003)
nail art dust suction collector nail cleaner tools (NC-001)